The content down below in relation to Installing A Bathtub is particularly enlightening. Read it for yourself and decide what you think of it.
Installing a tub isn't specifically rocket science, however it does call for strong plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is also a moderately tough task. If the old tub is readily easily accessible, the task can move rapidly; if you need to open up a wall to eliminate the old bathtub and also position the new tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will certainly require an assistant to vacate the old tub and set in the new one. Make certain you have actually certified yourself for the job as well as are comfortable trying it. As opposed to working with a contractor to take control of a halfway-completed task, it is far better to consider employing one before you begin. Possibilities are you may need an expert plumber to make tube links.
This short article will assist you set up a brand-new tub in your shower room if you have actually currently acquired a brand-new bathtub and also do not need to alter the plan of your previous water system pipes.
Your tools and also product list need to consist of the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you should do is separate the supply of water. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The process of eliminating the existing taps can be quite bothersome as a result of the limited gain access to that is typically the case.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will originate from the pipes. When the supply pipelines have been eliminated, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from transforming during this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Prior to moving on to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in area between the faucet and the sink. Safeguard the tap in position with the manufacturer given backnut. Once the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap ports. The previous type needs to be connected to the tap finishes initially, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Making use of both wooden boards under its feet, place the tub in the called for position. The wooden boards are valuable in equally spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small factors.
The next goal is to guarantee that the tub is leveled all round. This can be attained by examining the spirit level and changing the feet on the tub till the level reviews level.
To install taps, fit the bottom of the outermost versatile faucet adapter to the appropriate supply pipe by making a compression join; then do the same for the other tap.
Turn on the water system and also examine all joints as well as brand-new pipework for leakages as well as tighten them if needed. Load the bath tub as well as additionally examine the overflow electrical outlet and also the normal electrical outlet for leakages.
Lastly, take care of the bath paneling as described in the producer's instruction manual. Tiling and sealing around the bathtub should wait until the bathtub has been used at least once as this will certainly settle it into its last setting.
Preparing for the Installation
To start with, the sustaining framework supplied with the bath ought to be fitted (if required) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is very important to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps unit to avoid strain on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets using 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must now be ready to be suited its final setting.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack a stiff seal, creating the water to penetrate the wall in between the bathroom and the tiling, causing difficulties with dampness as well as feasible leakages to the ceiling below.
You can select from a range of coloured sealers to blend in your fixtures as well as installations. They are marketed in tubes and cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to enable the activity experienced when the bathtub is in use. The sealant can split relatively very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is advisable to fit the tiles utilizing waterproof or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed reading our piece about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks for taking a few minutes to read through our piece of content. Appreciated our article? Please share it. Help other people locate it. Many thanks for taking the time to read it.
Book Now!